top of page
Search
How to Install Television Backlight Strips Safely

How to Install Television Backlight Strips Safely

6 days ago
6 min read

A backlight strip can make a wall-mounted television look sharper, reduce the harsh contrast between a bright screen and a dark room, and add a clean finishing touch to a media wall. But when you install television backlight strips, the quality of the result comes down to preparation. Poor positioning, weak adhesive and untidy cable routing can quickly turn a small upgrade into something that looks uneven or stops working after a few weeks.

For most homes, LED backlight strips are a straightforward addition. The job becomes more technical when the TV is already on the wall, sits close to the wall, or has concealed cables. Taking a few minutes to plan the installation protects the television, keeps the lighting even and avoids having to remove the TV again later.

Choose the right type of television backlight strip

Not all LED strips work in the same way. A standard USB-powered strip provides a fixed or remote-controlled colour around the rear of the TV. It is usually the simplest option and is ideal for ambient viewing in the evening. Many switch on and off with the television if plugged into a USB port that supplies power only when the TV is running.

Wi-Fi and app-controlled strips offer more colour options, timers and voice control. These suit households using Alexa, Google Home or Apple HomeKit, although compatibility should always be checked before fitting. They normally need a separate power supply, so cable planning matters more.

Screen-reactive lighting is the more advanced option. A camera or HDMI sync box reads what is happening on screen and changes the lights to match. It can look impressive for films, sport and gaming, but installation takes longer and the equipment needs careful positioning. A basic strip is often the better choice for anyone who simply wants a comfortable glow behind the television.

Before buying, measure the rear of the TV rather than relying only on the advertised screen size. A 55-inch TV from one manufacturer can have a noticeably different rear panel size from another. Buy a strip that matches the usable perimeter and check whether it can be cut safely at marked cut points.

Prepare the TV and wall before fitting

Switch the TV off at the mains before starting. If the set is wall-mounted, assess the gap between the back of the television and the wall. Backlight strips need room for the light to spread. A very slim fixed bracket may leave too little space, creating a narrow bright line rather than an even halo.

As a general rule, a gap of around 50mm to 100mm gives better results. This depends on the brightness of the strip, wall colour and television size. A dark feature wall absorbs more light, while a white or pale grey wall reflects it strongly. If the television is close to a dark wall, a brighter strip may be needed, but do not set it so bright that it distracts from the screen.

Clean the rear panel of the TV where the strip will sit. Use a soft cloth with a small amount of isopropyl alcohol if suitable for the TV finish, then allow the surface to dry completely. Dust, grease and heat are the main reasons self-adhesive strips start peeling away.

Do not attach lighting over ventilation slots, heat vents, speaker openings or labels that need to remain visible. Television backs can become warm during long viewing sessions, and blocking airflow is never worthwhile for the sake of a neater line.

How to install television backlight strips evenly

Start by laying the strip around the back of the television without removing the adhesive backing. This dry run shows where the connector, controller and power lead will finish. In most cases, it is best to begin at the lower edge nearest the TV's USB port or the route to the nearest socket.

Set the strip in from the outer edge of the TV, usually by about 50mm. Keeping this distance consistent is more important than getting it exact to the millimetre. If one side is much closer to the edge than the other, the light will look uneven on the wall.

When you are happy with the route, peel a short section of backing at a time and press the strip firmly into place. Do not pull the strip tight around corners. Instead, make a gentle bend or use corner connectors if supplied. Pulling too hard can damage the LED circuit and causes strips to lift later.

Keep the controller in an accessible position where possible. Hiding it behind the television is fine, provided it is not trapped against the wall or placed over a vent. If it uses an infrared remote, the receiver may need to face downwards or sit somewhere the remote can reach. App-controlled systems give more flexibility because the controller can remain hidden.

For larger televisions, especially 65 inches and above, use the fixing clips supplied with the kit if available. The adhesive may hold at first but can weaken over time due to heat. Small clear clips placed carefully along the top and sides provide a more reliable finish without being visible from the front.

Avoid cutting until you have tested the lights

Many strips can be trimmed, but only at the marked cutting points. Cutting elsewhere can stop part or all of the strip from working. It is safer to fit and test the lights first, then decide whether an excess section needs to be shortened or tucked neatly behind the TV.

Connect the power lead and test every colour or brightness setting before tidying cables. Look at the television from the normal viewing position with the room lights low. You are checking for dark patches, overly bright corners and any visible LEDs shining directly out from the side.

Power and cable routing for a tidy finish

A USB-powered strip is often the cleanest option for a wall-mounted TV because the cable can stay behind the screen. However, TV USB sockets vary. Some provide enough power only for low-output strips, while others remain powered in standby, leaving the lights on after the television is switched off.

Check the strip's power requirement against the TV USB output in the manufacturer instructions. If there is any doubt, use the supplied mains adaptor rather than overloading the USB port. The adaptor should be connected to a proper socket, not squeezed behind the television or covered by furniture.

Where cables are visible, use small cable clips or trunking to guide them down the wall. Avoid running low-voltage LED cables tightly alongside mains cables for long distances where possible, particularly if the light strip flickers. Keep enough slack for the TV bracket to move if it is on an articulated or tilt-and-swivel mount.

Never drill into a wall simply to hide a lighting cable unless you know what is behind it. Electrical cables and pipes can run in predictable zones from sockets and switches, but assumptions are not enough. A professional wall mounting installation can plan cable routes, bracket position and backlighting together before the television goes up.

Common problems after fitting LED backlights

If the strip falls off, remove it carefully, clean the surface again and use suitable replacement adhesive pads or clips. Do not use heavy-duty glue that could damage the TV casing or make future removal difficult.

If the lights flicker or turn off when the TV starts, the USB port may not provide enough current. Try a suitable mains adaptor. If colours are wrong or part of the strip does not illuminate, check that any connectors are fully seated and that the strip has not been bent sharply at a corner.

Uneven light is usually a positioning issue. Move the strip slightly further in from the TV edges, reduce the brightness, or assess whether the wall finish is causing the problem. Backlights work best as a soft surround, not as the main light source in the room.

When it makes sense to get help

Fitting a strip is simple on a TV that is easy to reach. It is less convenient when a large TV is already fixed high on the wall, installed above a fireplace, or connected to several consoles, soundbars and hidden cables. Removing and refitting a heavy screen safely often needs two people, the right tools and confidence with the existing bracket.

We Fit All can fit television backlight strips as part of a TV wall mounting or media setup job across London, Essex and Kent. This is particularly useful where the TV needs to be repositioned, cables need organising, or a new bracket and lighting need fitting at the same time.

A well-fitted backlight should disappear when the TV is off and improve the room when it is on. Keep the glow even, keep the cables controlled, and let the screen remain the focus.

 
 
 

Comments


Contact  Us  Now

Tel:  07425 390 869

Mon-Fri:   07.00 - 23.00

Sat-Sun:    07.00  - 21.00

​

WeFitAll9@gmail.com​

 

400 Bonham Road

Dagenham 

RM8 3BB

 

We respond quicker to Text messages and calls as we see them instantly but do check emails daily.It is best to call or send use 

Thanks for submitting!

© WeFitAll

bottom of page